A combined children's suit (overalls) is a universal item of children's wardrobe. Lightweight and soft overalls can be worn everyday for babies from birth to 3 years. Insulated, waterproof products for autumn, winter and spring are an indispensable item in the wardrobe of boys and girls up to primary school age.

The cut of summer and demi-season models is the same for boys and girls if the product is intended for babies no older than 3 years. Patterns of winter overalls of small sizes are also universal. A special construction will be needed to make a light jumpsuit for a girl 4-10 years old.

Building a demi-season model

The universal pattern is designed to make an insulated outdoor model that is suitable for children from 1 to 8 years old. The model consists of two parts - a jacket and trousers.

When starting to design, it should be remembered that the combined demi-season product for children should be not only warm, but also comfortable, not hindering freedom of movement. When cutting trousers, it is necessary to take into account the fractional direction of the thread.

liveinternet.ru

Working process

1. The contour of ready-made garments (jackets and trousers) that fit the child well is duplicated on the fabric. You can also use ready-made patterns for children's clothing items that are part of the overalls. And also - circle pre-sorted things on the fabric, the size of which can be varied.
2. To the level of the waist of the front panel of the trousers, substitute the shelf of the upper part. Place the waist level of the front trouser part below the back.
3. Combine the back of the trousers with the back of the jacket.
4. Separately cut out the sleeve.
5. Before cutting the fabric for this model, it is recommended to perform a trial version of the product from the test material according to the available measurements or contours. In the case of a successful fitting, after making the necessary adjustments, the cut is transferred to the main fabric.
6. The lining fabric is cut first, then the insulation, then the top fabric layer. After the lining fabric is sewn to the insulation, the pattern should be increased by 1 cm around the entire perimeter. Next, the cut is transferred to the main canvas.
7. Regardless of whether the model is cut off or one-piece, it is recommended to sew a zipper from the neckline to the beginning of the fit line of the front of the trousers.

liveinternet.ru

Construction of a semi-overalls pattern

The universal semi-overalls will suit boys and girls up to 8 years. The product can be lightweight or insulated. Has no sleeves. Pants length is variable.

The design can consist of four or eight parts, depending on the cut of the thing (cut-off or one-piece).

Working process

1. The contours of the finished T-shirt and trousers of the child are duplicated. The back of the trousers should be raised at waist level so that the front is lower.
2. If the model is insulated, the construction increases by 1-5 cm on the sides of each part.
3. In the upper part of the trousers, front and back, you can sew in two strips of reflective edging, after cutting the details in the appropriate places (if the model is demi-season).

liveinternet.ru

Sewing the legs

A certain difficulty is the process of stitching the legs of a semi-overalls with long trousers, especially if the model is insulated.

Working process

1. Sew the crotch seams first.
2. Close the center seam to the point where the zipper will begin.
3. Performing a trouser seam in the center, turn one leg inside out, and the other on the face. Insert one leg into the other. Align the parts according to the front sides. Lay machine line.
4. Sew the area for the zipper by hand.

liveinternet.ru

Building a model for a girl

The pattern of overalls for a girl is intended for the manufacture of a summer combined model. The design consists of three parts - a top, short trousers and ruffled sleeves. The top element will be two parts with folds, and the bottom one will be four separate parts (two front and two back panels).

Working process

1. Duplicate the contours of the finished T-shirt and shorts, suitable in size. The front waist of the shorts should be lower than the back.
2. Cut out the sleeves based on the shoulder measurement and the armhole width of the top of the product. Two pieces of frill sleeves should be expanding strips of arbitrary width. Their length is equal to twice the measure of the armhole width of the top. The decorative sleeve will be a continuation of the neckline.
3. The cut of the neck and the upper edge of the sleeve are gathered with the help of a drawstring and pulled together with an elastic band.
4. After combining the top with shorts, the jumpsuit is supplied with an elastic band at the waist.

Lightweight overalls for children are sewn from denim, cotton or linen. Summer models for kids are made of fleece, flannel, knitted fabrics.

Products related to outerwear are made of waterproof fabrics impregnated with moisture protection. Evaporation of excess heat is facilitated by special high-tech membrane sheets. Their effectiveness, however, is achieved only by combining the upper "membrane" with a synthetic lining fabric - for example, fleece.

It is important to ensure that the insulation in overalls for babies under 2 years old on the shelf and back is at least 200 g per 1 sq.m. Volume on sleeves and trousers may decrease. Usually, models for sedentary children under one year old are insulated with synthetic winterizer. For older children, there are a number of materials that bear the names of officially registered trademarks.

Children love winter very much, because this is the most fabulous time of the year. Matinees, Christmas trees, gifts, meeting with the wizard Santa Claus, who fulfills the most cherished desires and brings so many goodies - all this is Winter! The first snow transforms nature, dressing cities in white clothes, and calls us to go out for a walk with our kids, run along snow-covered paths, lie in soft fluffy snow. Winter games are the most fun! You can go sledding or skating, play snowballs, make a snowman. And in order not to freeze during walks, you need to dress properly so that it is warm and comfortable, especially for a child.

We offer you the perfect option for winter clothes - insulated overalls with a hood. It is soft, cozy, fastened with a zipper, and will reliably protect from frost. And if a cold wind blows, you can put on a protective hood and any frosts will be nothing. In this lesson, you will learn how to build a basic pattern of baby overalls, according to which you can model and sew various models for both boys and girls, you just have to use your imagination!

For calculations and pattern drawing, use your child's measurements. In the lesson we use standard measurements of size 28 for a height of 104 cm.

Children's measurements required for construction (height 104 cm size 28) (for details see):

1. Chest girth (OG) - 56 cm
2. Waist circumference (FROM) - 53 cm
3. Hip circumference (OB) - 61 cm
4. Neck girth - 28 cm
5. Front length to waist (accident) - 27 cm
6. Shoulder length (Dpl) - 8.5 cm
7. Back length to waist (DTS) - 25.5 cm
8. Armhole depth - 14 cm
9. Hip height - 14 cm
10. Sleeve length (DR) - 36 cm
11. Wrist girth - 12.5 cm
12. Arm circumference at the top - 19.5 cm
13. Leg length from the outside - 63 cm
14. Leg length from the inside - 45 cm
15. Knee height - 35.5 cm

The width of the bottom of the trousers - 32 cm (the value depends on the model and personal preferences and can be increased or decreased)

Merck seat height is calculated as follows: Measure 13 minus Measure 14 = 63-45=18 cm. You can also measure the height of the seat.

Rice. 1. How to take baby measurements

16. Control measure of planting depth(Fig. 2) - measured from the 7th cervical vertebra along the back, passing a centimeter tape between the legs, to the jugular cavity along the front. This measurement is necessary to control the finished base pattern. For a comfortable fit, the pattern measurement should be 3-4 cm larger than the measurement taken.

Rice. 2. Control measure of planting depth

IMPORTANT! The increase in freedom of fitting to the Half-Circumference of the Chest is selected individually, base the choice of the amount of increase based on the thickness of the fabric and insulation, as well as the desired style of the overalls - from 4 to 8 cm. In the presented basic pattern, the increase is 8 cm. All necessary calculations will be performed in building process.

Basic pattern of baby overalls - building a grid

We start the construction from the upper left corner of a sheet of paper, put point A. Grid width: AA1 \u003d ½ OG + 8 cm \u003d 56/2 + 8 \u003d 36 cm.

From point A, draw down the segment AD \u003d Back length to waist + Leg length from the outside + 6 cm (increase for fit and lapel) \u003d 25.5 + 63 + 6 \u003d 94.5 cm.

From point A1, release a vertical line down, from point D draw a horizontal line to the right. Point D1 is obtained at the intersection.

Armhole line. AG \u003d Armhole depth + 1.5 cm (increase) \u003d 14 + 1.5 \u003d 15.5 cm.

Waistline. From point A, lay down the segment AT \u003d DTS + 2 cm (increase) \u003d 25.5 + 2 \u003d 27.5 cm. Draw a horizontal line of the waist TT1.

Hip line. From point T, lay down the segment TL \u003d 14 cm (Hip height by measure). Draw a horizontal line of the hips, points L1 and L2 are obtained.

Step line. From point T, lay down the segment TC = 18 cm (Seat height) + 2 cm (increase for landing) = 20 cm.

Knee line. TK = 35.5 cm. Draw a horizontal dotted line of the knee, points K1 and K2 are obtained.

Pants bottom line. DH = 4 cm (trouser lapel). Draw a horizontal dotted line at the bottom of the trousers HH1.

Draw horizontal segments from the marked points - points G1, T1, L1, C1, K1, H1, D1 are obtained.

Side line. Divide GG1 in half (point G2) and draw a side line vertically through point G2.

Rice. 3. Pattern of baby overalls

Building a pattern for the bodice of a jumpsuit

back pattern

Back neckline. From point A, set aside to the right 1/6OSh + 1 cm = 28/6 + 1 = 5.5 cm and 1.5 cm up (for all sizes). Draw the back neckline along the pattern.

Armhole width. G3G4 \u003d Bust / 4 + 2 cm (increase) \u003d 28.5 / 4 + 2 \u003d 9 cm. From the point G1 to the left and right, set aside G2G3 \u003d G2G4 \u003d 4.5 cm (½ Armhole Width).

Back shoulder line. From point P, lay down 2 cm and draw a short horizontal auxiliary line.

Draw a back shoulder line equal to the length of the shoulder according to the measurement + 1 cm (increase) so that the extreme point of the shoulder lies on the auxiliary horizontal segment.

From the lower corner of the armhole, draw a perpendicular 2 cm long. Draw the armhole of the back as shown in the drawing.

shelf pattern

Front lift. From the waist line, lay up T1A1 \u003d Length of the front to the waist (accident) + 2 cm (increase) \u003d 27 + 2 cm \u003d 29 cm.

Shelf neck cutout. From point A1 with a radius R = 1/6OSh + 1 cm = 28/6 + 1 = 5.5 cm, draw a cutout for the neck of the shelf.

Spend the length of the shoulder of the shelf in the same way as the shoulder of the back.

Building a pattern of trousers

Front half of pants

From point C1, set aside to the right C1C3 = 1/10 Half circumference of the hips + 0.5 cm = 3.1 + 0.5 cm = 3.6 cm. C1C4 = C1C3. Draw the line of the C3C4 bow along the pattern.

Connect points C3 and H1 with an auxiliary straight line. Set aside 0.5 cm at a right angle from the center of C3H1 and draw a slightly concave seam line.

The bottom line of the front half of the trousers. H1H2 \u003d 1/2 The width of the bottom according to the measure - 1 cm \u003d 32 / 2-1 \u003d 15 cm. Lengthen the segment D1D2 on each side by 0.3 cm. Draw the arrow line vertically upwards from the center of the segment H1H2.

Back half of trousers

From point C, set aside CC4 = 1/4 CC2 + 1 cm = 18.25/4 + 1 = 5.5 cm to the left. Draw a segment C4L along the pattern.

Arrow line. Divide the segment C4C2 in half and draw an arrow line as shown in the drawing - points K4 and H3 are obtained.

The width of the bottom of the front half of the trousers is calculated by the formula: ½ The width of the bottom according to the measure + 1 cm = 32/2+1=16+1=17 cm. Set aside 8.5 cm from point H3 to the left and right. Points H4 and H5 were obtained. Lengthen segment D3D4 on each side by 0.3 cm.

Connect points L2 and H4 - point K3 is obtained.

Measure the segment K4K3 and set aside the same value from the point K4 to the left: K4K5 \u003d K4K3. Connect the points C4K5, set aside an auxiliary perpendicular 0.7 cm long through the center of the segment to the right and draw a slightly concave line along the pattern.

On the shelf, build a detail of the stitched strap with a width of 3.5 cm, reshoot the detail of the strap on tracing paper separately. On the pattern, mark the width of the drawstring for the elastic.

Sleeve pattern for overalls

Build a sleeve pattern as shown in fig. 4. CC2 = 3/4 Depth of the armhole according to the pattern of the overalls.

Rice. 4. Sleeve pattern for baby overalls

Hood pattern

To build a hood pattern for a jumpsuit, you need to take 2 measurements: Head circumference and Head height (distance from the articulation of the neck with the shoulder to the top of the head).

Rice. 5. Hood pattern for baby overalls

The basic pattern of overalls is ready. You can use it without modification, or model the style according to your sketch. Details of the cut of the overalls are shown in fig. 6.

Rice. 6. Details of the cut of the children's hood

And now - a surprise for those craftswomen who completed the lesson and read the article to the end! We have prepared for you a basic pattern of overalls for a child in size 26-28 (height 104 cm) in full size and you! We wish you colorful ideas, bright models and a fabulously fun winter!

To build a pattern drawing, take the following measurements.

Half neck.

Half bust.

Half hip.

Back length to waistline.

Shoulder length.

Back width.

The length of the sleeve.

Pants length on the side.

Pants length to the knee.

Seat height.

Building a drawing.

Back and front halves.

Overalls length. Draw a vertical line on the left side of the sheet, on which set aside the measurement of the length of the back plus the measurement of the length of the trousers plus 4 cm and put points A and H.

Draw horizontal lines from points A and H to the right.

Overalls width. From point A to the right, set aside the measurement of chest girth (Og) divided by 2 plus 8 cm and set point B. From point B, lower the perpendicular to the lower horizontal line, mark the intersection point as H1.

Back length to waistline. From point A down, set aside the measurement of the length of the back to the waist line plus 2 cm and set point T. From point T to the right, draw a horizontal line until it intersects with line BH1, mark the intersection point as T1.

seat height. From point T down, set aside a measurement of the height of the seat plus 2 cm and put a point W. From point W to the right, draw a horizontal line, the point of intersection with the line BH1, designate W1.

hip line. From point W up, set aside 1/3 of the measurement of the height of the seat and set point B. From point B to the right, draw a horizontal line, mark its intersection point with line BH1 as B1.

knee line. From point T down, set aside the measurement of the length of the trousers to the knee plus 1 cm and set point K. From point K to the right, draw a horizontal line, mark its intersection point with line BH1 as K1.

Back width. From point A to the right, set aside the measurement of the width of the back divided by 2 plus 1.8 cm and put point A1.

Armhole Width. From point A1 to the right, set aside ¼ measurements of the half-girth of the chest plus 1.8 cm and put point A2. From points A1 and A2, draw down vertical lines.

Back neckline. From point A to the right, set aside 1/3 measurements of the half-girth of the neck plus 1 cm and put point A3. From point A3, restore upward a perpendicular, on which set aside 1/10 measurements of the half-girth of the neck plus 1 cm and set point A4. Divide the angle AA3A4 in half, from point A3 along the dividing line of the angle, set aside 1/10 measurements of the half-girth of the neck and set point A5.

Connect points A4, A5, A with a smooth line.

Shoulder cut back. From point A1 down, set aside 2 cm for normal shoulders, 1.5 cm for high, 2.5 cm for sloping and put a point P. Connect points A4 and P with a straight line, on which from point A4 set aside the measurement of shoulder width plus 1.6 cm on the tuck plus 0.5 cm on the landing and put a point P1.

Set aside 4 cm from point A4 along line A4 P1 and set a point O. Draw a vertical line down from point O, on which set aside 6 cm and set a point cO1. Set aside 1.6 cm from the point O along the line A4P1 and set the point O2. Connect points O1 and O2. From the point O1 along this line, set aside the length of the segment OO1 and set the point O3. Connect points O3 and P1 with a straight line.

Back armhole depth. From point P down, set aside ¼ measurements of the half-girth of the chest plus 7 cm and set point G. Draw a horizontal line through point G, mark the point of intersection with the line AN G1, with the line limiting the width of the armhole - G2, with the line BH1 - G3.

Back armhole line. Set aside 1/3 of the length of the PG segment plus 1 cm from the point G upwards and set the point P2.

Divide the corner G of the armhole in half, from the point G along the dividing line of the angle, set aside 1/10 of the width of the armhole plus 0.9 cm and set the point P3.

The width of the armhole - segment GG2 - divide in half and put a point G4. Connect points P1, P2, P3, G4 with a smooth line.

Front armhole depth. From point G3 up, set aside ½ measurements of the half-girth of the chest plus 4.5 cm and put point B1. From point G3 up, set aside ½ measurements of the half-girth of the chest plus 4.5 cm and put point B1. From the point G2 up, set aside the length of the segment G3B1 and set the point B2. Connect points B1 and B2 with a straight line.

Front neckline. From point B1 to the left, set aside 1/3 measurements of the half-girth of the neck plus 1 cm and put point B3.

From point B1 down, set aside 1/3 measurements of the half-girth of the neck plus 2 cm and put point B4.

Connect points B3 and B4 with a dotted line, divide it in half. Connect the bleeding point with a dotted line to point B1. From point B1 along this line, set aside 1/3 measurements of the half-girth of the neck plus 1.5 cm and put point B5.

Connect points B3, B5, B4 with a smooth line.

Auxiliary points for the design of the front line. Set aside ¼ from point G2 up

measurements of the half-girth of the chest plus 6 cm and put a point P4.

From the point G2 up, set aside 1/3 of the length of the segment G2P4 and set the point P5.

Divide the angle P5G2G4 in half, from the point G2 along the dividing line of the angle, set aside 1/10 of the width of the armhole plus 0.6 cm and set the point P6.

Shoulder front cut. Draw a straight line from point B3 through point P4. On this line from point B3, set aside the measurement of the length of the shoulder and put point P7.

armhole front line. Connect points P7, P5, P6, G4 with a smooth line.

Side cut of the top of the jumpsuit. From point G4, lower the perpendicular to

line HH1. Mark the points of intersection with the lines of the waist, hips, seat height, knee and the lower horizontal line T2, B2, W2, K2 and H2. Point B2 ends the line of side cuts of the top, below is an auxiliary line for constructing sections of the trouser part.

Front cut line. Draw a horizontal line from point Ш1 to the right, on which, from point Ш1, set aside 1/10 measurements of the half-girth of the hips plus 0.5 cm and put point Ш3.

Set aside the same segment from the point Ш1 up and put the point Ш4. Connect points Ш3 and Ш4 with a dotted line, divide it in half. From the division point, restore the perpendicular down, on which set aside 0.3 cm. Connect the points B1, 0.3, W3 with a smooth line.

Fold line. Divide the line Ш2Ш3 in half, mark the division point as Ш5. Draw a vertical line through point W5. Mark the points of its intersection with the lines of the waist, hips, knee and lower horizontal, T3, B3, K3, H3.

The bottom line of the front half of the jumpsuit. From point H3 to the left and right, set aside ½ measurements of the width of the bottom of the trousers minus 1 cm and put points H4 and H5.

Set aside 0.5 cm from point H3 upwards and connect the resulting point with straight lines to points H4 and H5.

Side cut front. Connect points B2 and H4 with a straight line.

Step cut of the front half. Connect points Ш3 and Н5 with a dotted line, divide this line in half. From the division point to the left, restore the perpendicular, set aside 1-2 cm on it and connect the resulting line with a smooth line with points W3 H5.

Auxiliary point for the design of the line of the middle cut. From point W to the left along the horizontal line, set aside 1/10 measurements of the half-circumference of the hips plus 0.5 cm and put point W6.

Back fold line. Divide the line Ш6Ш2 in half, mark the division point as Ш7. Draw a vertical line through point W7. The points of intersection of this line with the lines of the waist, hips, knees and the lower horizontal mark T4, B4, K4, H6.

Pitch line extension. From point W6 to the left along the horizontal line, set aside 1/10 measurements of the half-circumference of the hips plus 2.5 cm and put point W8.

Bottom line of the back. From point H6 to the left and right, set aside ½ measurements of the width of the bottom of the trousers 1 cm and put points H7 and H8. Set aside 0.5 cm from point H6 down and connect the resulting point with straight lines to points H7 and H8.

Side cut back. Connect points B2 and H8 with a straight line. Mark the point of intersection of this line with the knee line as K5.

Knee Width. From the point K4 to the left, set aside the length of the segment K4K5 and put the point K6.

Step cut back. Connect point K6 with a straight line to point H7 and a dotted line to point Ш8. From the W8 point down the dotted line, set aside 1 cm and put the W9 point. Divide the segment Ш9К6 in half, restore the perpendicular from the division point to the right, on which set aside 0.5 cm. Connect the resulting point with a smooth line with points Ш9 and К6.

Middle cut line. Connect points T and Ш9 with a smooth concave line.

Sleeve construction.

Length. On the left side of the sheet, draw a vertical line, on which set aside the measurement of the length of the sleeve and put points A and H. Draw horizontal lines from these points to the right.

Width. From point A to the right, set aside the width of the armhole from the overalls drawing, multiplied by 3, minus 1 cm, and set point B. From point B, lower the perpendicular to the lower horizontal line, mark the intersection point as H1.

Eye height. From point A down, set aside ¾ of the depth of the armhole of the back and set point O. From point O to the right, draw a horizontal line, mark its intersection point with line BH1 as O1.

eye line. Divide the line OO1 into six equal parts, mark the division points as O2, O3, O4, O5, O6. From these points, draw vertical lines upward, mark the points of intersection with the AB line as A1, A2, A3, A4, A5.

From point O2 upwards, set aside 1/3 of the height of the eye minus 0.5 cm and set points A7 and A8.

From point O6 up, set aside 1/6 of the height of the eye and set point A9.

Connect points O, A6, A7, A3, A8, A9, O1 with a smooth line.

bottom line. Continue the A3O4 line down, mark its intersection point with the HH1 line as H2. Set aside 2-3 cm from the H point to the right and put the H3 point. Divide the H3H2 segment in half, set aside 0.5 cm from the division point down and connect the resulting point with a smooth line to the points H3 and H2. Set aside 2-3 cm from point H1 to the left and put point H4. Divide the H4H2 segment in half, set aside 0.5 cm from the division point upwards and connect the resulting point with a smooth line with points H4 and H2.

Article from the site

I sewed this baby overalls for the baby at the end of winter - the beginning of spring, when it is still quite cold outside. Then we were still very young, we only lay on walks, so we wanted to sew warm and comfortable clothes. I took the jumpsuit pattern from the children's clothing magazine Ottobre (No. 4 - 2004), which, in my opinion, is the best magazine for children's clothing patterns.

I sewed in size 68 (according to height), but this pattern can also be sewn in other sizes: 56-62-68-74-80-86.

In detail 3 - from below +2 cm!

The fabric for the overalls is polyester on a synthetic winterizer (quilted), if desired, you can insert another layer of insulation (wool, holofiber). For older children, you can use maida insulation, thinsulate - they are thin, but warm, so they are great for babies who are starting to walk on their own, and they just need light clothing that will not hinder their movements. Lining - cotton, you can knit. It is better to choose natural fabric, because it is in contact with the face and body of the child.

Details (from the main fabric and lining):

1. Breast - 1 child. with a fold.

2. Side inserts in front - 2 children.

3. Back - 2 children.

4. Sleeve - 2 children.

5. Hood - 1 child.

6. Plank - 1 child.

I added a chest pocket and cuffs on the sleeves and legs to cover the legs and arms.

Additionally, I needed two zippers (I took a length of 40 cm, you can 50 cm), Velcro.

I will dwell in more detail on the process of sewing children's overalls. I completed this task in a few evenings))

Pocket. We sew the main fabric of the pocket with the lining from the wrong side, turn it inside out. We sew along the edge and sew a pocket on the chest.

Lightning. Sew the zippers to the chest, but without lining.

We sweep, then, together with the lining fabric, sew along the front side. Similarly, we sew the second half of the zipper to the side inserts of the front.

If the zippers are detachable, then the connection point of the zipper can be closed with a patch (I used a piece of brown leather).

Back and sleeves. We carry out the middle seam of the back on the main fabric and on the lining separately.

Then we also sew the sleeves along the raglan line to the main fabric and lining.

Sew the crotch and side seams. These parts of the main and lining fabric are sewn separately. Then we turn the lining inside out and insert it inside the overalls.

Hood. We sew the details of the hood, leaving open the edge that is sewn to the neck. Turn inside out, stitch along the edge.

We sew the main fabric of the hood to the collar, and then the lining fabric to hide the seam, sew it with a blind seam or sew it off.

Plank. A strap must be sewn onto the chest so that the neck and hood fit snugly around the neck. We sew the details of the bar, turn it inside out, stitch it out. We sew one half of the Velcro to the ends of the strap, and sew the other half to the hood. The length of the Velcro should be chosen so that you can fasten the bar tighter and weaker.

Ready-made pattern of children's semi-overalls Height 98-100 Chest 56-58cm

The pattern of children's semi-overalls is designed for approximately a three-year-old baby. Since children even at this age are of different builds, because they have moms and dads of different builds, before cutting, you need to check the height and girths of the child.

A table of sizes for children's clothing, as well as the ratio of the age, height, chest circumference and weight of the child can be

This children's semi-overalls can serve as a great addition to the jacket, which was discussed in, and can be a full-fledged independent item of a children's wardrobe.

This children's jumpsuit is suitable for both boys and girls. It can be practical, waterproof, warm, winter and demi-season, depending on the chosen top fabric (bologna, corduroy, jeans, etc.), lining, insulation, etc.

Preparing a pattern for work is extremely simple.

Click on the diagram at the end of the article and pattern of children's semi-overalls will open in a new window.

Print the pattern sheets on the printer, cut and connect them in accordance with the diagram.

Be sure to check the scale. On a printed sheet with a 10x10 cm square depicted, the sides of 10 cm should correspond to exactly 10 centimeters.

If you have any difficulties with printing patterns, write to us and we will post a master class with the details of this process.

Compare the sizes of the patterns with your child's measurements. Make changes if necessary.

Additionally to the existing parts of the semi-overalls, it is necessary to cut out placket under the zipper, 6cm wide plus seam allowances (finished 3cm), strap length approximately 30cm.

In the proposed model of semi-overalls, a zipper is located in the side seams of the bottom of the legs. You can change the processing of this part of the product at your own discretion. For example, several rows of elastic tape (gum) can be laid along the bottom of the legs, or a drawstring can be made and an elastic cord with a lock can be sewn on, a strip of knitwear about 4-6 cm wide can be sewn on. The choice is yours.

In the drawstring along the waist line, as well as in straps an elastic band is inserted between the control marks, due to this, a good fit of the product on the baby's figure is ensured.

Knee pads and padding on the back of the pants provide additional protection from the cold, keeping your little one comfortable in inclement weather.

You can change the finished pattern if necessary. Lengthen, widen, narrow the bottom, etc.

A skillful mother or grandmother-needlewoman can decorate a jumpsuit with embroidery or appliqué.

The lining is cut according to the main details.

Don't forget to add seam allowances.