Hooray! Finally we made it! So, we present to your attention a master class on making blocks for doll shoes. Since we do textile dolls, then we will make pads for them. We do not undertake to claim that this is the only true way to make pads. But that's how we do it. So let's get started.
Osinka is the only resource besides my blog where I post this MK in full. If you want to place MK at your place, then first coordinate this issue with me.

First we make a master model. For this:

We sew an additional leg. In order for the fabric to become solid and give support to plasticine, we impregnate it 3-4 times with PVA glue.

We dry each layer of PVA. To speed up drying, you can put the workpiece in the oven, heated to 50-70 degrees. The oven door should be ajar so that moist air can freely escape and the workpiece dries, and does not bake.

We put the dried blank on a piece of binding, or other dense, cardboard and circle it. This will be the sole of the shoe.

We try on again, trying to imagine how the sole will be combined with the shape of the boot.

Glue a plasticine edge onto the cardboard sole

to fill the gap between the foot and the sole.

We cover the gap.

From plasticine we form a block. The shape and size of the shoe should match the shape and size of the future boot or shoe. When sculpting a block model, you need to give a small allowance for the final processing of the block.

We take a block of plasticine and cut off the plates from it.

We draw a line along the master model that divides it in half. Glue the cut plasticine plates along this line.

Having glued the model around, we cut the plates with a rectangle.

We make sides from thick cardboard. The height of the sides should be such that when casting over the model, a layer of gypsum about a centimeter thick would be obtained. At the exit point of the model from the box, we make a plasticine rim.

We strengthen them with plasticine. The result should be a box with sides made of cardboard and a bottom made of a model pasted over with plasticine. Check, for clearance, the absence of cracks. If there is, cover them with plasticine. If this is not done, the solution will leak out.

We lubricate the resulting structure with a thin layer of petroleum jelly.

Pour COLD water into a plastic container. The colder the water, the more time grasping alabaster. The volume of water is about half the volume of the solution that you want to get in the end.

Gradually pour alabaster into the water. Alabaster is a building gypsum. You can use any plaster, sculptural or medical, but alabaster is cheaper and sold at any hardware store. True, it is coarser, but in this case it is not critical. We pour alabaster while it sinks. The view from above should be similar to the photo. If you pour less, it will be liquid, if dry islands remain, they will turn into lumps when stirred. After pouring, immediately stir and pour into the form. Do not pull for a long time - the plaster sets quickly.

Pour the solution into the mold carefully, trying to pour the model first. It is necessary that the solution gets into all corners.

DO NOT pour any leftover solution down the sink or toilet! Gypsum seizes even under water. Even if you pre-diluted the solution, the gypsum will settle and seize inside the sewer pipes. If there is a lot of solution left, pour it into a trash bag. Leave the residue on the walls of the container until it sets. Then remember her. I hope you took a plastic container, as we advised? The layer of hardened gypsum will rebound.

By the way, the hardening of gypsum on the walls of the container and its bouncing off them is a good indicator that the form can be disassembled.

We disassemble the form and pull out the model from it.

In the form, with the tip of a knife, we make two indentations.

We put the model back and build a cardboard box around it.

WITH reverse side we coat the cracks by gluing the cardboard walls to the already cast half of the mold.

Lubricate with Vaseline. We breed gypsum, fill it, wait until it hardens.

We remove the cardboard walls.

Let's break down the form. ATTENTION! It is necessary to wait for the complete setting of the gypsum mortar, 30-40 minutes. If you hurry, the mold may break.

We dry the form in an ajar oven at a temperature of about 70-80 degrees. DO NOT overdo it with the temperature! At 100 degrees, water, as you know, boils and the form can be torn apart by steam. The dried form brightens and becomes much lighter. We usually leave it to dry overnight. You can, of course, dry it in the air, but it's too long.

Final stage. We make a column.

Lubricate the mold with Vaseline.

We fold the halves of the form and bandage. We dilute the gypsum mortar and pour it.

After hardening, we separate the form. Do not hurry. If you hurry, the casting will break. We are waiting for about 30-40 minutes. In order to separate the form, insert the tip of the knife into the gap between the halves of the form and turn.

Again, using a knife, we take out the casting from the second half of the mold.

On a wet casting with a knife removes irregularities. To get rid of irregularities, "shells" from air bubbles, knead the gypsum shavings and cover the irregularities with it. If the chips are dry, wet them first.

After drying the pads in the oven, bring them to the right sizes, shape and smoothness of sandpaper. The main thing is not to overdo it. It will no longer be possible to fix it.

We impregnate the pads with a primer deep penetration or diluted PVA. We leave to dry.

And cheers! The pads are ready. You can start making shoes. We will definitely do a master class on making shoes on a block, but we don’t know exactly when ...

Dolls have been the favorite hobby of most girls at all times. They can be not only a children's toy, but also an original interior decoration. Nowadays, even well-known design houses are engaged in the production of clothes and shoes for toy fashionistas. Since this is basically, such shoes will not be cheap. You can make doll shoes yourself from a wide variety of materials.

There are several ways to make shoes for a doll with your own hands. The simplest and most common of them is to glue shoes or sandals together. More experienced craftswomen can sew doll accessories. High boots are made in this way. Knitted slippers or booties for baby dolls can be crocheted or knitted.

Another fairly simple solution is to paint the shoes on the doll's legs with acrylic paints. This method does not limit either in materials, or in color, or in the style of shoes.

However, there is one significant drawback - such shoes are made forever without the possibility of taking them off.

Shoe materials can be very different:

• denim or any dense fabric;
• soft fleece;
• satin and lace;
• leatherette;
• thin leather or suede;
• for the sole - cardboard, thick skin, Cork.

For decoration, you can use thin laces, beads and beads, eyelets and sequins. Eyelets can be used plastic or metal. They are installed on holes in the material through which the laces will be pulled. The choice of materials for tailoring and decorating doll shoes can only be limited by the manufacturer's imagination.

To make shoes for a doll with your own hands, you will need tools for work:

• needles with threads;
• centimeter tape and ruler;
• sewing machine;
• scissors;
• quality glue;
• knife for leather and leatherette;
• acrylic paints and brushes;
• device for installing eyelets.

Creating a pattern

To make shoes for a doll, you can download and print ready-made patterns. Experienced needlewomen can make patterns of boots for dolls with their own hands. To do this, it is important to have a clear idea of ​​what the finished shoe will look like. The model is developed taking into account the entire costume.

If the image of the doll is based on a certain historical period, you can look for information in the relevant literature.

Master class on building a shoe pattern for a doll:

1. The very first step in the manufacture of any shoe pattern is the construction of the outline of the sole. To do this, the puppet leg is applied to a sheet of paper and carefully outlined.
2. If it is planned to manufacture model shoes, the sock is completed.
3. Further, the pattern of the sole narrows slightly in three places: near thumb, in the instep area and on the widest part of the foot. So the finished shoes will fit better to the leg.
4. To build the upper part, the doll's leg is measured with a centimeter tape: the volume of the foot, the height of the back, the height of the product in front.
5. It is very important to remember the seam allowances - leave a few millimeters.

Via finished pattern it will be possible to create a wide variety of models.

Doll sneakers

You can make your own pattern for this shoe. The downloaded finished pattern can be transferred to a Word document and there you can ensure that the value matches the size of the puppet leg. To do this, the length of the foot is pre-measured with a ruler or centimeter tape. Be sure to make allowances of 5 mm on all sides.

You can make an insole pattern yourself if you circle the foot with a pencil on paper and cut it out.

To make a caddy you will need:

The sole of this model is made of three layers of materials. Bottom part cut out of rubber, a layer of corrugated cardboard is glued on it. An insole is placed on top of any soft tissue, can be in the color of all shoes.

When the sole is ready, the rest of the details are fixed to it. They can be attached with pins.

Such a blank should be easy to put on the leg.

A leatherette sock is sewn onto the upper part of the boots or sneakers. The top and sides are machine stitched. Holes for laces are pierced and eyelets are inserted. Both uppers are pinned to the sole and stitched by hand to assemble the entire structure.

The places where the sole and the upper part are sewn together are sealed with a dense cotton tape or linen elastic. You can temporarily fix the tape with pins until the glue dries.

Colored laces are pulled into ready-made sneakers.

Sandals for Barbie

Making shoes for Barbie with your own hands is not difficult. As with any shoe, the first step is to outline the outline of the foot. First, it is done on paper, and then transferred to thick cardboard. If necessary, you can more clearly draw an elongated toe of sandals or shoes.

Pasted on a cardboard base the cloth. The resulting piece is bent to the shape of the foot. On the upper part at the junction with the sole allowances and small notches are made throughout the length. This will glue the upper to the sole. To connect these parts top part applied to the leg and folded under the foot. The part of the sole is glued from below.

In the same way, the back is cut out and glued in the right place. The heel is cut out immediately with a strap on which a loop for the clasp is cut.

From wooden skewers you can cut out the heels and glue them to the soles of the sandals. To do this, a piece of skewer is pasted over with the same fabric from which all shoes are made. Shoes for Barbie are ready.

Monster High shoes

Monster High is one of the girls' favorite toys. You can make boots for a doll from this series according to the same principle as for Barbie. For example, it can be high boots made of elastic material.

The sequence of actions will be as follows:

Paola Reina boots

For a Paola Reina doll, you can sew low, simple boots. The product is designed for a toy with a height of 32 to 34 cm. Such shoes can be easily removed from the block and from the doll's foot. General principle work - the pattern of parts must be done along the transverse line, and not along the shared line. The finished shoes will then stretch in width, and it will be much easier to take them off.

For work you will need:

• leatherette;
• thick cardboard 1.2-1.4 mm thick;
• eyelets - 4 pieces;
• linoleum or rubber for soles;
• foamiran or rubber strips for prophylaxis 6x160 mm in size - 2 pieces;
• glue Moment for shoes;
• Glue Supermoment second.

All details will be cut out of leatherette, cardboard and sole material.

The work algorithm should be as follows:

Paola's shoes are ready. It is important to allow the glue to dry thoroughly before use. It remains to put a leatherette insole inside, and you can put on boots on your pet.

Any girl, whether she is big or small, loves to play with dolls. And not just to play, but also to sew clothes and shoes for her. Nowadays, there is a whole industry for the creation of both one and the other. And for Barbie dolls, outfits are sometimes created even worldwide famous designers. Of course, these are oh so expensive. And often they are created by hand, because the size of the product simply does not allow the use of technical devices. And from this their price increases even more. To create, first of all, patterns and sketches are needed. That is why in this article we will look at how to create do-it-yourself shoe patterns for dolls. And let's look at this different types dolls with different shape and foot size.

Where to get ideas

In order to create a pattern, you must first draw a sketch. And in order to draw it, you need to more or less clearly imagine how the future shoes will look like. That is, there must be an idea. And where can I get it? They usually develop the idea of ​​shoes either together with the main suit, or after it is ready. Before making shoe patterns for your doll, look for something suitable for your doll in books or magazines, among shoe models presented in stores. It is also worth rummaging through historical sources if the image of your dolls is related to historical characters or time periods. In general, inspiration can be found anywhere.

Ways to create doll shoes

Shoes for dolls are produced different ways. It can be glued. And this is one of the most common ways to create various shoes and sandals. Shoes can be sewn. Especially one that has high tops or does not have a dense sole. It can be or booties. Also, shoes can be crocheted or knitted. But there is another method that is especially successfully used on textile dolls. Shoes can be simply painted with acrylic paints. This method is good because it does not limit you in any way. With the help of paint and brushes, you have the right to draw anything you like, without caring at all that your idea cannot be fulfilled or that you suddenly cannot find the necessary materials. But there is one significant downside. These shoes are forever. You can't get rid of her doll. Therefore, the most convenient and interesting option is to make shoes that are beautiful, unusual, realistic, and at the same time replaceable. It is in this case that we can not do without patterns.

What are doll shoes made of?

Materials for doll shoes are selected in a variety of ways. It can be leather and leatherette, jeans and others. The sole is usually made of cardboard or cork material. Often soft and elastic materials are used to create shoes. Fabrics that easily take the desired shape. It all depends on your idea. Boots are best made from leather or its substitutes, shoes from bright, shiny or satin materials, but booties or slippers are made from cozy fleece. If you want to make shoes out of lace, then it is better to treat it, for example, with a sealant, so that it keeps its shape. In general, you can use almost anything. The difference is only in the complexity of processing the material.

Additional decorations

In addition to the main material, you will need all sorts of additional decorative elements. It could be ribbons beautiful threads, lace, beads, beads, eyelets, sequins. As well as thin laces, hanging elements and various other no less interesting materials. Everything depends on fantasy.

Tools and materials

Of course, you will need threads and needles. And also scissors. Be sure to get good glue. After all, very often shoes for a doll do not have to be sewn, but glued. Also a very useful thing when creating shoes for dolls is the eyelet installer. Eyelets are metal and plastic. They are installed on the holes, thereby strengthening the fabric around them. These reinforced holes are used to tighten the laces. It will not be superfluous to have acrylic paints in the arsenal for tinting the necessary details.

The basic principles of creating a pattern of shoes for dolls with your own hands

In the development of shoe patterns, as well as in the development, there are certain principles. So to speak, the basis from which are then modeled various forms and models. Creating a shoe pattern for dolls with large feet, as well as small ones, begins with the insole.

Work should begin with the contour of the foot. To do this, put the doll's foot on a sheet of paper and circle it. Now we decide on the shape of the shoe and finish drawing the sock. After all, you need to narrow the insole a little in three places. This is the place of the thumb, the widest place on the foot, as well as the instep zone. All this is necessary so that in the end the shoes fit the foot better. Second important point is the construction of the upper part. To do this, you need to measure the foot with a centimeter in several places. Using the results of these measurements, which must be at least three, we create a form. Of course, it will have to be adjusted for the most part. Just apply the paper base to the leg and determine where and what needs to be adjusted. Don't forget to measure the height of the back. This will be the basis of any pattern. The sole matches the insole, but is a couple of millimeters wider. When the base is ready, you can use it to create almost any model.

Shoes for dolls with large feet

In this section of the article, we will try to figure out how to make shoe patterns for big-footed dolls with our own hands. Consider this process using the example of shoes. First, an insole is also created according to the shape of the sole.

To sew shoes, you need to understand what parts these shoes consist of. In addition to the insole, the boot should contain side parts, as well as a top and a “tongue”. After completing the insole, proceed to the side parts. They can be cut in one piece or consist of two. But then they are sewn together, and the seam is located behind. In order to build the side patterns of shoes for big-footed dolls, it is necessary to measure the length of the side part. From its beginning on one side, through the heel and to the end on the other side. As well as the length of the tops of boots or boots. If you have two parts planned, then the constructed pattern should be divided into two parts exactly in the middle.

To create boots, it would be nice to have an eyelet installer. With its help, the holes made in the side parts are strengthened. Laces will be tucked into these holes. Now we will make a pattern of the upper part. To do this, we take the insole as a basis and cut out the upper part according to its shape and extend it to the desired length so that it goes into the “tongue”. When all the patterns of shoes for big-legged dolls are ready, we cut them out of matter and assemble them together. And when everything is already sewn and glued to the insole, we make the sole and attach it to the boot. It is better to collect shoes directly on the doll. Just pre-wrap the foot with cellophane so as not to glue the boot directly to the foot. You can decorate the finished shoe as you wish.

Sandals for Barbie

Patterns of shoes for Barbie dolls are quite simple. First of all, a foot contour is created on the necessary material and duplicated on thick cardboard. The shape of the sock is drawn additionally, if necessary. For example, if you want to make a pointed toe or an elongated one.

The fabric base is glued to a cardboard blank and bent to the shape of the foot. The top of the sandals is cut out according to the shape of the toe of the sole. A small allowance is made along the edge and notched all over. It is needed to glue it to the plantar part. To do this, we apply the sole and the upper part to the leg and wrap the incised allowance on the underside. We glue everything with reliable glue. In the same way, we create a backdrop, which we cut out immediately with a strap and attach it to the heel. We make a loop on the strap and sew the bead to the back. Using wooden skewers, you can make a heel for sandals.

To do this, cut off the desired length of the skewer and glue it with the same fabric. Now it remains just to glue the heel to the sandals - and that's it. You can wear beauty.

Shoe patterns for Monster High dolls

Monster High dolls are very popular today. Girls like to create not only furniture and rooms for their toys, but also clothes and shoes. Do-it-yourself shoe patterns for Monster High dolls are made similarly to those for Barbie dolls. Consider them using the example of creating high boots.

From a suitable fabric, two blanks are cut out in the shape of the legs so that their length ends half a centimeter below the toes. The workpiece is wrapped around the leg and stitched so that it fits snugly around the leg. It is better if the fabric is slightly elastic. The seam should be placed at the back, in length it should reach the heel. In the same way as for the Barbie doll, we make the sole out of cardboard and bend it to the shape of the foot.

We attach a cardboard blank to the doll’s foot and, cutting the edge of the boot, glue it to the sole, and on top we glue another, final sole and heel, which is done in the same way as for Barbie sandals.

Slippers for Tilda

Patterns of shoes for Tilda dolls are created according to the principles already discussed earlier. An insole is created from cardboard, which, for beauty, is pasted over with the fabric from which the entire slippers will consist. We apply the insole to the sole and glue the top of the slipper on it. To hide traces of fixation, a sole is attached from below. It is better to choose a fabric for shoes that is denser, but the sole should not be too hard, otherwise it will be difficult for you to put it on the doll's leg when the slipper is finished. It remains only to make your slippers more exclusive. You can achieve this with the help of an unusual decoration.

Booties for Baby Born dolls

Now a fairly popular doll is Baby Born. The kids are very fond of playing with her, and the game process certainly includes a change of outfits and shoes. Therefore, we will definitely analyze shoes for

Most often, booties are created for these dolls, because these baby dolls are so similar to babies. But the meaning of building a pattern does not change from this. We still circle the sole, only we don’t need to narrow any places. And we create the top according to the same principle that was described earlier. The cutout on the bootie-slipper, if necessary, is done by eye. Only the distance from the fingertips to its presumed beginning is measured beforehand. In this case, the top and side parts are cut in one piece. A seam is made at the back, and then the upper part is joined to the lower part with a blind seam. The booties do not have a dense sole, so in this case everything is connected with a needle and thread. And, of course, do not forget about decoration.

We have reviewed various options creating a pattern of shoes for dolls with your own hands. With great attention should be paid to details and decor. After all, it is they who make it unique, unlike any other. And this is exactly what every master wants to achieve. And not only a beginner, but also already wise with experience. So don't be afraid to be imaginative. The main thing - remember that everything should be moderate and compatible.

Patterns shoes for bigfoot dolls collected in this article will be useful for lovers of these cute textile dolls.

After all, any puppeteer - whether she is big or small - loves to dress up her dolls. And many doll lovers simply love to create clothes for their favorites with their own hands.

Today, in the world of dolls, there is a widely developed industry for tailoring outfits for little fashionistas. Even eminent designers are engaged in outfits for dolls. However, often clothes and shoes for dolls are very expensive. So much so that it is easier to sew or make everything you need on your own.

Especially when it comes to a unique big-legged doll that you sewed yourself. For such dolls, as a rule, the owners sew clothes and shoes themselves. Today we decided to talk about the intricacies of creating boots for big-footed dolls.

In order to sew boots for your doll, you will need, first of all, patterns and sketches that have been tested and tested by craftsmen. Based on them, you can build your own patterns and sew a new thing for your doll.

This inspired us to create a series of articles in which we decided to collect the most popular shoe patterns for bigfoot dolls. And we decided to start with the simplest workshop on sewing textile boots for your doll.

Patterns shoes for big-legged dolls: boots. Master Class

Here is a small photo tutorial on making boots for a doll fashionista.

Textile dolls, as a rule, do not have standard sizes and are sewn by each hostess according to the dimensions that suit her.

Therefore, measurements are taken from each model individually and transferred to patterns shoes for bigfoot dolls . When cutting the fabric, do not forget to leave allowances for the seams.

How to dress up bigfoot

Recall that big-footed dolls or snowball dolls are a very popular type. textile dolls. They are usually from 25 centimeters and above. Proportions are what unites the big dolls sewn by different craftswomen and makes them different from other dolls. These textile dolls big head and legs, small eyes are embroidered or drawn exactly in the center of the round face.

Bigfoots are often called snowballs because housewives like to dress them up in sweaters and hats with pom-poms.

Also on the big-legs you can often see fur capes and warm boots, felt boots and raincoats, coats and ponchos. Bigfoots are very fond of wrapping up warmly - this is how it happened with lovers of these textile dolls.

A bigfoot must wear not only a hat or headband, but also shoes, as well as socks or stockings.

Based on the book by Nadezhda Gensitskaya. The book is very good, but the techniques are "boots", with pulling on the blocks. As a result of various attempts, I realized that it was difficult for me and not very exciting.

But I wanted to make shoes. I remembered how I sewed dance slippers for my daughter and went this way.

Puppet master class. Begin. To begin with, we will sew such simple, red (or white) slippers.

The pattern will look like this. If, after scanning, the insole matches the size of the foot, then the shoes made according to this pattern should fit your doll. If the insole is small, you need to enlarge the entire drawing to scale until the size of the insole matches the size of the doll's foot. If the insole is large, reduce.

Two "small" insoles made of rubber and four "large" ones made of any cotton fabric are needed.
"Small" insoles should be exactly the size of the foot. “Large”, + 0.5 cm allowance.

We sew “small” rubber insoles between two cotton ones and sew a “large” one to these blanks. From the red (main) fabric


We cut out the upper part of the shoe from the main red fabric. Pattern of the upper part, immediately with allowances for the seams. If the shoes are made of leather, then you can immediately sew the top to the insole. If from taffeta, as in our case, the top must be “planted” on the lining. As a lining, I use lining jersey. We fold the two parts and sew the inner contour, turn it inside out.



We sew the details of the top along the heel line. It turns out two blanks of slippers, without soles.
We apply the top to the sole. Make sure that the red details are facing inward. facing each other. We sew.
The seam that holds the upper to the sole should wrap neatly around the small rubber insole. Do not catch the rubber insole with the seam. WE REVERSE!
SHOE READY! Shoes can be decorated to your liking. Good luck!